Search results

Super-tall towers have surfaced as a pragmatic remedy to meet the escalating requisites for both residential and commercial areas and to stimulate economic growth in the Middle East. In this unique regional context, optimizing spatial usage stands as a paramount consideration in the architectural design of skyscrapers. Despite the proliferation of super-tall towers, there exists a conspicuous dearth of comprehensive research pertaining to space efficiency in Middle Eastern skyscrapers. This study endeavors to bridge this substantial gap in the literature.

The research methodology utilized in this paper adopts a case study approach to accumulate data regarding super-tall towers in the Middle East, with a specific focus on investigating space efficiency. A total of 27 super-tall tower cases from the Middle East were encompassed within the analytical framework.

Key findings can be succinctly summarized as follows: (1) average space efficiency was 75.5%, with values fluctuating between a minimum of 63% and a maximum of 84%; (2) average ratio of the core area to the gross floor area (GFA) registered 21.3%, encompassing a spectrum ranging from 11% to 36%; (3) predominantly, Middle Eastern skyscrapers exhibited a prismatic architectural form coupled with a central core typology. This architectural configuration mostly catered to residential and mixed-use functions; (4) the combination of concrete and outrigger frame systems was the most frequently utilized; (5) as the height of the tower increased, space efficiency tended to experience a gradual decline and (6) no significant discernible disparities were detected in the impact of diverse load-bearing systems and architectural forms on space efficiency.

Despite the proliferation of super-tall towers, there exists a conspicuous dearth of comprehensive research pertaining to space efficiency in Middle Eastern skyscrapers. This study endeavors to bridge this substantial gap in the literature.

The purpose of this paper is to identify the relationships between consumers' body types and characteristics such as shopping orientation, past experience with fit problems, attitudes toward internet shopping and attitudes toward 3‐D body scanning.

This study collected body data from 441 Korean females who participated in 3‐D body scanning. Using a hierarchical cluster analysis, the body scanning identified five body types. Then body types and shopping characteristics variables were analyzed.

Slim respondents showed significantly higher hedonic shopping orientation and their attitude to internet shopping was positive, since they evaluated using the internet as being “fun”. By contrast, respondents with larger body types considered the convenience of internet shopping to be the most important feature. Respondents, regardless of their body types, regarded 3‐D body scanning as an enjoyable, futuristic and interesting experience. Moreover, respondents showed a high inclination to spend more money for customization services which utilize the 3‐D scanning technique.

This study analyzed Korean females' body shapes using 3‐D scanned body measurements. This study can contribute to integrate knowledge in the body measurement sector and the consumer behavior sector.

The purpose of this paper is to assess tall women's satisfaction with the fit and style of apparel for tall women.

A total of 75 US women, who were at least 5 feet 8 inches and between 18 and 54 years old, were asked to rate their level of satisfaction with misses‐size and tall‐size apparel, in general, and with seven garment categories (jackets/blazers/coats, button‐up blouses, pullover tops/sweaters, skirts, jeans, pants, lingerie).

T‐tests revealed that participants were more satisfied with the fit of tall‐size apparel than with the fit of misses‐size apparel, but were more satisfied with the style of misses‐size than with the style of tall‐size apparel. In addition, participants most frequently used the misses‐size designation to purchase clothing and rated style as more important than fit. Despite reported dissatisfaction with the fit of misses‐size apparel, participants appeared willing to sacrifice fit to have the desired styles.

The study was limited to US women in Southwestern Virginia. Thus preferences affected by regional product offerings may be reflected in the responses.

The paper provides discussion on implications of mass customization in resolving the conflict tall women report between the desire for properly fitting apparel and the desire for current style trends.

No existing empirical research has examined tall women's satisfaction with products specifically designed for their special anthropometric and style preference needs. This research serves as the foundation for extending research for the market segment from an applied and basic research approach.

Long-run changes in living standards occupy an important place in development and growth economics, as well as in economic history. An extensive literature uses heights to study historical living standards. Most historical heights data, however, come from selected subpopulations such as volunteer soldiers, raising concerns about the role of selection bias in these results. Variations in sample mean heights can reflect selection rather than changes in population heights. A Roy-style model of the decision to join the military formalizes the selection problem. Simulations show that even modest differential rewards to the civilian sector produce a military heights sample that is significantly shorter than the cohort from which it is drawn. Monte Carlos show that diagnostics based on departure from the normal distribution have little power to detect selection. To detect height-related selection, we develop a simple, robust diagnostic based on differential selection by age at recruitment. A companion paper (H. Bodenhorn, T. Guinnane, and T. Mroz, 2017) uses this diagnostic to show that the selection problems affect important results in the historical heights literature.

Supertall towers (300 m+) offer a viable solution to the increasing demand for housing and commercial space caused by rapid urban growth, migration from rural to urban areas and economic expansion in Asia. In this particular context, the efficient utilization of space becomes a crucial factor in the design process for Asian skyscrapers as they seek to address the changing socioeconomic landscape. This study will provide valuable guidance, especially to architectural and structural designers in the pursuit of sustainable development for Asian skyscrapers by analyzing space efficiency.

The methodology employed in this paper involved a case study approach to gather data on 75 Asian supertall towers in order to examine space efficiency.

Findings of the research can be summarized as follows: (1) the average space efficiency of these towers was 67.5%, ranging from a minimum of 55% to a maximum of 82%; (2) the average proportion of the core area to the gross floor area (GFA) was 29.5%, with values ranging from 14% to 38%; (3) the majority of Asian skyscrapers exhibited a tapered form and adopted a central core typology, which catered to mixed-use and office purposes; (4) the most frequently utilized structural system was a combination of composite and outriggered frames; (5) space efficiency tended to decrease as the height of the tower increased; and (6) there was no noteworthy difference in the impact of various load-bearing systems and building forms on space efficiency.

There is a noticeable lack of extensive research into space efficiency in supertall towers in Asia, which serves as a hub for skyscrapers. This study seeks to fill this substantial gap in the current scientific literature.

The purpose of this paper is to analyze the phenomenon of makeup effect using numerical simulation and model experiments on seven different natural smoke extraction patterns of tall space. Airflow distribution and heat accumulation phenomenon in different cases are compared. The natural smoke exhaust system for tall spaces has many advantages, including low cost, no power and low maintenance cost. It is more advantageous than the mechanical type of exhaust. However, the internal air distribution is complicated since the large span spatial character. Effective and correct verification method is very important for the analysis of flow fields in tall spaces.

This study used fire dynamics simulator (FDS) software to simulate the fire scene. The model experiments are conducted to determine if the numerical simulation results are reasonable. A single-mirror Schlieren system, including an 838 (H) × 736 mm (W) square concave mirror, as well as the focal length of 3,100 mm was adopted to record the dynamic flow of hot gas. Six smokeless candles were burned in a 1/12.5 model in experiments to record the distribution of inflow, accumulation and outflow of airflow in the space. In addition, the thermocouple lines were mounted in the model for temperature measurement.

The results of numerical simulation and model experiments have proved that makeup air has a significant effect on the effectiveness of a natural smoke vent system. Larger areas of smoke vents will produce more heat accumulation phenomenon. In this study, the air inlet and vent installed on the same side have a better heat removal effect. Moreover, Schlieren photography technique is proved to be an accurate measurement method to record the dynamic flow of hot air immediately, directly and accurately. The dynamic flow behavior of hot gas in the model has been visualized in this paper.

At present, there is no examination method other than checking the smoke vent area to validate the effectiveness of a natural smoke vent system in Taiwan, as well as no requirements regarding the makeup inlet. The effect of makeup air in generating the effective push-pull phenomenon of airflow has been analyzed. In addition, the post-combustion hot gas distributions were visualized by using Schlieren photography technology in the model space, compared with the FDS simulation result and thermocouple recorded temperature. A verification method in the model experiments is established to determine if the numerical simulation results are reasonable.

To date, there are no studies in the literature that provide a comprehensive understanding of the interrelationships between the slenderness ratio and the main design criteria in supertall towers (=300 m). In this paper, this important issue was explored using detailed data collected from 75 cases.

This paper was carried out with a comprehensive literature review including the database of the Council on Tall Buildings and Urban Habitat(CTBUH) (CTBUH, 2022), peer-reviewed journals, MSc theses and PhD dissertations, conference proceedings, fact sheets, architectural and structural magazines and other Internet sources. In this study, the case study method was also used to gather and consolidate information about supertall towers to analyze the interrelationships. Cases were 75 supertall buildings in various countries [44 from Asia (37 from China), 16 from the Middle East (6 from Dubai, the United Arab Emirates), 11 from the United States of America and 3 from Russia, 1 from the UK].

The paper's findings highlighted as follows: (1) for buildings in the height range of 300–399 m, the slenderness ratio was usually between 7 and 7.9 and megatall towers were frequently built at a slenderness ratio of 10–15; (2) the median slenderness ratio of buildings in the 400–599 m height ranges was around 8.6; (3) a trend towards supertall slender buildings (=8) was observed in Asia, the Middle East and North America; (4) residential, office and mixed-use towers had a median slenderness ratio of over 7.5; (5) all building forms were utilized in the construction of slender towers (>8); (6) the medium slenderness ratio was around 8 for supertall buildings constructed with outriggered frame and tube systems; (7) especially concrete towers reached values pushing the limits of slenderness (>10) and (8) since the number of some supertall building groups (e.g. steel towers) was not sufficient, establishing a scientific relationship between aspect ratio and related design criteria was not possible.

To date, there are no studies in the literature that provide a comprehensive understanding of the interrelationships between the slenderness ratio and the main design criteria in supertall towers (=300 m). This important issue was explored using detailed data collected from 75 cases.

The purpose of this paper is to analyze petite women’s body size and figure and investigate whether current petite sizing charts accurately reflect actual petit size women’s bodies. This study also categorizes petite women’s body shapes and suggests primary body measurements as a base size for each shape. The ultimate goal is to suggest fundamental body measurements for apparel companies to modify and improve their sizing.

This study used data from SizeUSA data to compare body measurements of 18-35-year-old petite women to regular women. The authors compared the results to measurement differences between petite and regular sizing charts of 14 apparel companies. Then, using the principal component analysis and cluster analysis, the authors classified petite women’s body shapes. Body measurements for each body type are contrasted with the current petite sizing charts, and then, the authors present differences as suggestions for modification and improvement of petite sizing.

Industry sizing system do not generally represent average petite size women preciously except for stature. Within the petite women, four body types were identified (top petite: 30.0 percent, bottom petite: 30.8 percent, regular petite: 23.6 percent, and plus size: 15.4 percent). Of the four groups, the ASTM D7878 generally represented the “top petite” sizing.

It is the first to analyze the industry petite sizing system utilizing population data and focus petite sizing for women aged 18-35. The authors believe this study could draw attention of the apparel industry, providing companies with ideas of how to improve their petite sizing for young women.

A detailed numerical study is conducted on the effect of surface radiation on laminar natural convection in a tall vertical cavity filled with air. The cavity is heated and cooled, through its two vertical walls, by a linear or uniform heat flux q(y) and by a constant cold temperature, respectively. The horizontal walls are considered adiabatic. The paper aims to discuss these issues.

The radiosity method is employed to calculate the net radiative heat exchanges between elementary surfaces, while the finite volume method is implemented to resolve the governing equations of the fluid flow.

For each heat flux q(y) (ascending, descending or uniform), the effect of the emissivity ε (0ε1) on the local, average and maximum temperatures of the heated wall is determined as a function of the average Rayleigh number Ra_m (103Ra_m 6×104) and the cavity aspect ratio A (10A80). The effect of the coupling on the flow structures, convective and radiative heat transfers is also presented and analyzed. Overall, it is shown that surface radiation significantly reduces the local and average temperatures of the heated wall and therefore reduces the convective heat transfer between the active walls.

The studied configuration is of practical interest in several areas where overheating must be avoided. For this purpose, a simple design tool is developed to estimate the mean and the maximum temperatures of the hot wall in different operating conditions (Ra_m, A et ε).

The originality lies in the study of the interaction between surface radiation and natural convection in tall cavities submitted to a non-uniform heat flux and a constant cold temperature on the active walls. Also, the development of an original simplified calculation procedure for the hot wall temperatures.

In the recent decades, an increasing trend has been observed in the steps North Korea has taken to open up to tourism. The purpose of this paper is to gain a deeper understanding of the influence the North Korean political ideology has on different aspects of international tourism.

Apart from the scarce academic literature, news media and internet resources, fieldwork that includes interviews with two international travel companies and a trip to North Korea contributed to gathering information from different perspectives.

It is not surprising that North Korean tourism cannot be divorced from its political context. By looking at the political influence exerted by the North Korean Government on the structure of the industry, tourism policies applied to the organization of tours and the content of tourism and marketing, this paper shows the existence of elements that remained unchanged in the last three decades, as well as new liberal elements that transform North Korea into a more open and versatile tourism destination.

Based on an analysis of primary and secondary data, this paper makes original contributions to North Korea tourism studies by investigating the influence of the political ideology on different aspects of tourism industry and on tourist experience.